日本积水流感病毒抗原检测试剂盒

日本积水流感病毒抗原检测试剂盒

广州健仑生物科技有限公司

广州健仑长期供应各种流感检测试剂，包括进口和国产的品牌，主要包括日本富士瑞必欧、日本生研、美国BD、美国NovaBios、美国binaxNOW、日本积水、日本荣研、美国OSOM、芬兰、爱思普林、英国Clearview、凯必利、广州创仑等主流品牌。

日本积水流感病毒抗原检测试剂盒

我司还提供其它进口或国产试剂盒：登革热、疟疾、流感、A链球菌、合胞病毒、腮病毒、乙脑、寨卡、黄热病、基孔肯雅热、克锥虫病、违禁品滥用、肺炎球菌、军团菌、化妆品检测、食品安全检测等试剂盒以及日本生研细菌分型诊断血清、德国SiFin诊断血清、丹麦SSI诊断血清等产品。

欢迎咨询

欢迎咨询2042552662

日本积水流感病毒抗原检测试剂盒

想了解更多的产品及服务请扫描下方二维码：

【公司名称】 广州健仑生物科技有限公司
【市场部】    杨永汉

【】 
【腾讯  】 2042552662
【公司地址】 广州清华科技园创新基地番禺石楼镇创启路63号二期2幢101-103室

包埋剂embedding agent 
在制作切片或超薄切片时，由于组织是柔软的，或局部的软硬不均，这样制作厚薄均匀的切片是困难的。所以有必要用一定物质浸透组织内部，整个组织一样硬化，以利于切成薄片，这种物质叫做包埋剂。一股用光学显微镜观察的切片，用石蜡、火棉胶、炭蜡、明胶等作包埋剂；电子显微镜则用环氧树脂、聚苯乙烯树脂、异丁烯树脂及水溶性树脂。 
石蜡制片法是将材料经固定、脱水、透明、浸蜡后包埋在石蜡里面进行切片的方法。此法适用范围，制片手段完备，能将材料切成极薄的片子（可切至2-8微米左右），并能制成连续的片子，这是其它制片法难以达到的，因此在光学显微镜的制片技术上它是zui常用的一种方法。除了一些经不住石蜡切片法中所应用的各种药剂处理的材料不能应用石蜡切片以外，一般的材料都可以用此法制片，但有制作时间较长，操作过程复杂以及材料易发硬或发脆等缺点。该法多采用旋转式切片机进行切片。
石蜡制片操作程序如下：  
（一）材料的采集与分割  
采集材料应根据制片的目的和要求而定，材料要有代表性，无病虫害或其它损伤，如要观察病理解剖，则要取病斑、病症部位。采下的材料应立即放在标本箱或湿布包起来带回实验室进行分割固定（如有条件也可在试验地采集后进行分割固定）。为使固定液能迅速的渗透材料，材料要进行分割。分割时动作要迅速，以防材料萎蔫。分割块的大小，宜小不宜大，一般不超过1cm3，分割后立即杀死固定。 

Embedding agent
In the production of sliced ​​or ultra-thin slices, because the tissue is soft, or local soft and hard uneven, so that the thickness of the slice is difficult to make. So it is necessary to use a certain substance soaked inside the tissue, the entire tissue as hardened to facilitate the cut into thin slices, this material is called embedding agent. An optical microscope observation of the sections with paraffin, collodion, charcoal wax, gelatin and other embedding agents; electron microscopy epoxy resin, polystyrene resin, isobutylene resin and water-soluble resin.
Paraffin preparation method is the material by the fixed, dehydrated, transparent, immersed wax embedded in paraffin inside the method of slicing. The scope of application of this method, the means of production is complete, the material can be cut into very thin films (can be cut to 2-8 microns), and can be made into a continuous film, which is difficult to achieve by other production methods, so in Light microscopy is technically the most commonly used method of making it. In addition to some paraffin sections can not be used in the treatment of various pharmaceutical agents can not use paraffin sections, the general material can be produced by this method, but with longer production time, the process is complicated and the material is easy to be hard or Crisp and other shortcomings. The law and more rotary slicing machine slicing.
Paraffin preparation procedures are as follows:
(A) material collection and segmentation
Collection materials should be based on the purpose and requirements of the film, the material should be representative, no pests or other damage, such as pathological anatomy to observe, you have to take lesions, the site of the disease. The collected material should be immediay put in the specimen box or wet cloth wrapped up and back to the laboratory for segmentation and fixation (if conditions can also be collected after the trial split and fixed). In order for the fixed liquid to rapidly penetrate the material, the material should be divided. Divide action to quickly, to prevent material wilting. Split the size of the block should be small should not be large, generally not more than 1cm3, killed immediay after the split.